How to scan for 3ABN Dare To Dream, Latino Radio and Proclaim

3ABN has added new channels 3ABN Dare to Dream (D2D) and 3ABN Latino Radio. The 3ABN Proclaim channel has been moved to a new frequency. Current Glorystar receivers will be automatically updated to receive these channels. Automatic updating models are: GEOSATpro DVR1100 / DSR100 / DSR200.

If you have an older receiver (Manhattan, Topfield, Fortec Star) the best method for updating your receiver for all of the Adventist Channels is to delete current programming, scan for the new channels then delete the unwanted channels. Free step by step instructions are provided below for receivers distributed by Adventist broadcasters.

We highly recommend the purchase of a complete Glorystar system or upgrade your old receiver with a new Glorystar receiver. Glorystar receivers have all channel changes in place and automatically update to add new channels as they become available. Please call us at 866-597-0728 and ask the sales team for a Glorystar system or receiver upgrade to watch all the current channels and automatically add any new Glorystar channels.

Adventist Channel Parameters for North America

Note: The Galaxy 19 satellite has had several names through the years. This satellite may be named in your receiver as: Telstar 5, T5, Intelsat America 5, IA5, Galaxy 25, G25, Galaxy 19 or G19.

If you are unable to program your receiver and wish to contract a local installer to assist, please visit an online satellite installer referral service at http://www.FTAinstall.com

To view the FREE update programming instructions,
click on your receiver model from the list below:

Receiver Brand: GEOSATpro DVR1100c / DSR100c / DSR200c - Instructions Glorystar System	Important Notice: Your FREE Adventist channel scanning instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment. If you require additional assistance, please contact the company or broadcaster where you originally purchased your satellite system. GEOSATpro DVR1100c / DSR100c / DSR200c receivers automatically update from the satellite and no manual channel programming is necessary. If you are not receiving the new channels or new channels are not automatically added to your receiver, verify that the Signal Quality (Q) reading on 3ABN (channel 106) is at least 50% and you are seeing television programming. If the Signal Quality is not at least 50%, the dish will need to be adjusted to increase the Signal Quality (Q) reading. To perform a Manual Update: Using your GEOSATpro remote control, press Menu button Left Arrow to Accessory Screen Down Arrow to OTA Press OK Verify Automatic Update setting is ON        (if OFF, Press Right Arrow to ON) Press Down Arrow to Update Now Press OK Screen displays" Do you want to update S/W?" Press OK After OTA update, the receiver will restart. Press Menu button Press VOL up button (the button that points to the right) three times to “UTILITY” menu Press the Channel up button (the button that points to the up) to highlight “FACTORY DEFAULT” Press OK button to display “ARE YOU SURE TO LOAD FACTORY DEFAULT?” Press OK button to restart the receiver. Press OK to select ENGLISH Press OK to select GLORYSTAR Press OK to select correct “TIMEZONE” then press OK Press VOL up button to set “DAYLIGHT SAVINGS” ON or OFF Press the Channel down button to highlight “NEXT” Press OK button to display “CONNECT COAX CABLE” screen Verify Signal Quality reading of at least 50% on 3ABN (channel 106) and on Cornerstone (channel 113) Press orange Signal button to remove signal quality meter The receiver date and time is automatically set by the satellite. Place the receiver on Channel 1 for at least 15 seconds to update Note: Failure to have Signal Quality of at least 50% and displaying television programming on 3ABN (channel 106) will prevent the receiver from automatically updating and adding new channels. Watch Receiver Programming Video Important Notice: Your FREE Adventist channel scanning instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment. If you require additional assistance, please contact the company or broadcaster where you originally purchased your satellite system. Manhattan DSR 1500 Reprogramming Instructions for 3ABN Proclaim 1. Using your Manhattan DSR 1500 remote control press “SETUP” button (located above the #3 button) 2. Press down arrow and highlight “SYSTEM SETTING” 3. Press OK button 4. Press down arrow and highlight “DEFAULT SETTING” 5. Press OK button and the screen will display “WARNING: THIS WILL RESET ALL SETTINGS TO DEFAULT VALUES” 6. Press right arrow to select “OK” 7. Press OK button and the screen will display “WARNING: ARE YOU SURE YOU WANT TO CONTINUE” 8. Press right arrow to select “OK” 9. Press OK button 10. Screen will Display “PLEASE WAIT” then “STORED SETTINGS RESET TO DEFAULT”, press OK button to restart the receiver 11. Screen displays LANGUAGE SELECTION, press OK button 12. Press down arrow to “TP FREQUENCY” 13. Using the number buttons on the remote control enter the numbers 11842 14. Press down arrow to select POLARIZATION should be “HOR” 15. Press down arrow to ‘SYMBOL RATE” 16. Using the number buttons on the remote control enter the numbers 22000 17. If you have good level yellow/green bar on “Signal Strength”, press down arrow to “Start Search” (there will be quotation marks “” on either end of Start Search when it is selected) 18. Press the OK button 19. A box will pop up to the right. When you see the word “Store” at the bottom of that box press OK button 20. Screen will display “CHANNEL DATA IS BEING UPDATED” then return to a TV viewing screen 21. Press "SETUP" button 22. Press down arrow to highlight "Channel Search" 23. Press OK button to display the "Channel Search Menu" 24. Press down arrow to “TP FREQUENCY” 25. Using the numerical keypad on the remote control enter the numbers 12060 26. Press down arrow to select POLARIZATION should be “HOR” 27. Press down arrow to ‘SYMBOL RATE” 28. Using the number buttons on the remote control enter the numbers 22000 29. If the reading on “Signal Strength” meter is not at a strong and high level, you may need to fine-tune the dish to receive the new Channel 30. Press down arrow to “Start Search” 31. Press the OK button 32. A box will pop up to the right. When you see the word “Store” at the bottom of that box press OK button 33. Screen will display “CHANNEL DATA IS BEING UPDATED” then return to a TV viewing screen To remove unwanted channels: 34. Press "SETUP" button 35. Press down arrow to highlight "Edit Channel List" 36. Press OK to display "Edit Channel List" Menu 37. "Delete" will be selected by default 38. Press the OK button 39. Use down and right or left arrow buttons to select an unwanted channel 40. Press OK to delete the selected unwanted channel 41. Repeat steps 38 - 40 to delete all unwanted channels 42. Press down arrow to select "STORE" 43. Press OK to save changes 44. Press ESC button to view TV programming DIRECTIONAL ARROWS ON THE REMOTE CONTROLS ARE THE “CHANNEL UP BUTTON (UP ARROW), CHANNEL DOWN BUTTON (DOWN ARROW), VOLUME UP BUTTON (RIGHT ARROW), VOLUME DOWN BUTTON (LEFT ARROW) Important Notice: Your FREE Adventist channel scanning instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment. If you require additional assistance, please contact the company or broadcaster where you originally purchased your satellite system. Manhattan SKYLINE 1000 Programming Instructions for 3ABN Proclaim 1. Using your Manhattan SKYLINE 1000 remote control press the “MENU” button 2. Press the down arrow to highlight “Master Reset” 3. Press the OK button two (2) times and the screen will display “Resetting - Please Wait” 4. Press ESC button to exit “OSD SETUP” 5. Press ESC button to exit “TV SETTINGS” 6. Press ESC button to exit “TIME SETTINGS” (or enter time settings and select STORE and press OK) 7. Press ESC button to exit “ANTENNA SETTINGS” 8. Press down arrow to highlight “Search Mode” 9. Press left arrow to select “Auto FTA” 10. Press the channel down button to highlight “TP DATA” 11. Press OK button 12. A box will pop up to the right. At the top of that box, in yellow, make sure it says “TP1:3ABN”, if not, push the left or right arrow to get to “TP1:3ABN” 13. Press down arrow to “FREQ” (frequency) 14. Using the numerical keypad on the remote control enter the numbers 11842 15. Press down arrow to “Polarity” 16. Press left arrow to select “HORZ.” 17. Press down arrow to “S/R” (symbol rate) 18. Using the numerical keypad on the remote control enter the numbers 22000 19. Press down arrow to “FEC” 20. Press left arrow to select ¾ 21. Press down arrow to “STORE” 22. Press OK button and screen will display “Storing Data – Please Wait” 23. Press OK button 24. A box will pop up to the right. At the top of that box, in yellow, make sure it says “TP2:ATN”, if not, push the left or right arrow to get to “TP2:ATN” 25. Press down arrow to “FREQ” (frequency) 26. Using the numerical keypad on the remote control enter the numbers 12060 27. Press down arrow to “Polarity” 28. Press left arrow to select “HORZ.” 29. Press down arrow to “S/R” (symbol rate) 30. Using the numerical keypad on the remote control enter the numbers 22000 31. Press down arrow to “FEC” 32. Press left arrow to select ¾ 33. Press down arrow to “STORE” 34. Press OK button and screen will display “Storing Data – Please Wait” 35. Press Channel down button to “START” 36. Press OK button and upon channel scan completion the screen will display “Resetting – Please Wait” To remove unwanted channels: 37. Press the "Menu" button 38. Press the right "VOL" arrow button to highlight "Edit" with "1 Channel Edit" yellow 39. Press the OK button, the screen will display "Channel Edit Menu" 40. Press the right "VOL" arrow button to change the function to "Delete" 41. Press the OK button to highlight a TV Channel yellow 42. Press the UP or DOWN "CH" button to highlight an unwanted channel to delete 43. Press the OK button two times, this will place a check mark beside the channel name 44. Press the UP or DOWN "CH" button to highlight additional unwanted channel to delete 45. Repeat steps 42 and 43 to select additional channels to delete 46. Press "ESC" button 47. Press "CH" down button to highlight "STORE" 48. Press the OK button to delete the selected channels 49. Prompt will display "STORING DATA, Please wait" 50. Press "ESC" button to view programming *DIRECTIONAL ARROWS ON THE REMOTE CONTROLS ARE THE “CHANNEL UP BUTTON (UP ARROW), CHANNEL DOWN BUTTON (DOWN ARROW), VOLUME UP BUTTON (RIGHT ARROW), VOLUME DOWN BUTTON (LEFT ARROW) Important Notice: Your FREE Adventist channel scanning instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment. If you require additional assistance, please contact the company or broadcaster where you originally purchased your satellite system. Topfield 3000/4000/6200 Programming Instructions for 3ABN Proclaim 1. Using your Topfield 3000/4000/6200 remote control press the “MENU” button 2. Press down arrow to highlight “Installation” 3. Press OK button 4. Press down arrow to select “Factory Setting” 5. Press OK button to display “Reset All Data” 6. Press left arrow to select “Yes” 7. Press OK button to display “Position Data Delete” 8. Press left arrow to select “Yes” 9. Press OK button to continue 10. Press up arrow to select “SAT/TP Edit” 11. Press OK button again on “Satellite Name” (A window listing satellite names will pop-up on the right hand side) 12. Press down arrow to select “Telestar5(KU)” or “Intel_Amc5(KU)” 13. Press OK button 14. Press down arrow to select “Add new TP” 15. Press OK button to display new window “Add New TP – “Frequency” will be highlighted 16. Using the numerical keypad on the remote control enter the numbers 11842 17. Press down arrow to select “Symbol Rate” 18. With the numerical keypad on the remote control enter the numbers 22000 19. Press down arrow to select “Polarization” and push the right arrow one time and it should display “Horizontal” 20. Press down arrow to the word “OK” and press the OK button on the remote control 21. "Add new TP" will be highlighted, Press "OK" 22. Using the numerical keypad on the remote control enter the numbers 12060 23. Press down arrow to select “Symbol Rate” 24. With the numerical keypad on the remote control enter the numbers 22000 25. Press down arrow to select “Polarization” and push the right arrow one time and it should display “Horizontal” 26. Press down arrow to the word “OK” and press the OK button on the remote control 27. Press down arrow to select “Channel Search” and press the OK button on the remote control 28. Press Channel down button to select “Search Mode” and press the Volume up button (the button that points to the right) one time and it should display “Manual” 29. Press down arrow to select Frequency and press left arrow "VOL" button to select 11842 MHz 30. In the lower right hand corner you will see two signal indicator bars, “Level” and “Quality”. The “Level” reading should be green and the "Quality" reading should be 50% or better. If the "Quality" reading is low, fine tune the dish aiming before scanning for channels. 31. Press Channel down button to select “Start Search” 32. Press OK button and a “Searching” screen will appear 33. When Channel Scan is completed press OK, the Channel Search Screen will appear 34. Press Channel down arrow button to select "Search Mode" and press the Volume up button (the button that points to the right) and it should display “Manual” 35. Press down arrow to select Frequency and press right arrow "VOL" button to select 12060 MHz 36. Press Channel down button to select “Network Search” and press the Volume up button (the button that points to the right) one time and it should display “Off”. 37. Press Channel down button to select “Start Search” 38. Press OK button and a “Searching” screen will appear 39. When Channel Scan is completed press OK, the Channel Search Screen will appear 40. Press Exit button to exit the menus and view the new programming To remove unwanted channels: 41. Press Channel up or down button to select "Organizing Channels" 42. Press the OK button to display "Organizing Channels" menu 43. Press Channel down button to highlight "Delete" Function 44. Press the OK button to enter the "Channel List" 45. Use the Channel up or down arrow button to highlight an unwanted channel 46. Press the OK button to select channel to be deleted, channel name will turn light gray 47. Press Channel up or down button to hightlight an additional channel to delete 48. Press the OK button to select channel to be deleted. (Repeat steps 47 and 48 for additional channels) 49. Press Exit button, a prompt will appear "Delete services. Are you sure?" 50. Press left arrow to select Yes and press OK 51. Prompt will show "Deleting Services", then will return to main "Main Menu" screen 52. Press exit to view programming DIRECTIONAL ARROWS ON THE REMOTE CONTROLS ARE THE “CHANNEL UP BUTTON (UP ARROW), CHANNEL DOWN BUTTON (DOWN ARROW), VOLUME UP BUTTON (RIGHT ARROW), VOLUME DOWN BUTTON (LEFT ARROW) Important Notice: Your FREE Adventist channel scanning instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment. If you require additional assistance, please contact the company or broadcaster where you originally purchased your satellite system. Fortec Star Mercury II Programming Instructions for 3ABN Proclaim 1. Using your Fortec Star Mercury II remote control press “Menu” button to go to "Installation" screen 2. Press the Channel down button to highlight “Factory Reset” 3. Press OK button to go to “Factory Reset” screen with Factory Reset line highlighted 4. Press OK button. A pop up window displaying "Are You Sure?" with "No" highlighted yellow 5. Press VOL down button to highlight "Yes" with yellow 6. Press OK button 7. When Language screen appears, turn off master power switch on back of receiver or unplug receiver from AC power outlet for 10 seconds 8. Turn the receiver back on or plug the receiver back into AC power outlet. "Language" Menu will appear 9. Press "Menu" to go to "Installation" screen with “Antenna Setup” highlighted 10. Press OK button to enter "Antenna Setup" screen 11. If needed, press VOL down button (the button that points left) to select "Galaxy25 Ku 97.0W or IA5/KU 97.0W" 12. Press the Channel down button to highlight “LNB TYPE” 13. Press VOL up button to display “LNB-10750” 14. Press the Channel down button to hightlight "0/22kHz" line and press the VOL up right arrow button to display On 15. Press the Channel down button to hightlight "Switch" line and press the VOL up right arrow button to display DiSEqC 1.0 16. Press the Channel down button to highligh "Input" line and press the VOL up right arrow button to display LNB 2 17. Press Menu button to go back to “INSTALLATION” screen, prompt will display "Saving" 18. Press the Channel down button twice to highlight “TP SCAN” 19. Press OK button to go to “TP SCAN” screen 20. Press the Channel down button to highlight “FREQUENCY” 21. Using the numbers buttons on the remote control enter 11842 22. Press Channel down button to highlight “POLARITY” and push the Volume up button (the button that points to the right) it should display “Horizontal” 23. Press Channel down to “SYMBOLRATE” 24. With the number buttons on the remote control enter the numbers 22000 25. Press Channel down to "Save Edit" line and press OK to store. Store prompt will show for a moment 26. On the bottom of the screen you will see two bars, one says “SIGNAL LEVEL” and the other “SIGNAL QUALITY” 27. If you have the “Signal Quality” bar with the highest strength (at least 50%), press Yellow button 28. When Channel Scan is completed, pop up window displaying "Do you want to save?" with "Yes" highlighted yellow 29. Press OK button to save. Programming will automatically be displayed 30. Press Menu button to enter “INSTALLATION” screen 31. Press the Channel up or down to highlight “TP SCAN” 32. Press OK button to go to “TP SCAN” screen 33. Press the Channel down button to highlight “FREQUENCY” 34. Using the numbers buttons on the remote control enter 12060 35. Press Channel down button to highlight “POLARITY” and if nessessary push the Volume up button (the button that points to the right) it should display “Horizontal” 36. Press Channel down to “SYMBOLRATE” 37. With the number buttons on the remote control enter the numbers 22000 if nessessary 38. Press Channel down to "Save Edit" line and press OK to store. Store prompt will show for a moment. 39. On the bottom of the screen you will see two bars, one says “SIGNAL LEVEL” and the other “SIGNAL QUALITY”. 40. Verify the “Signal Quality” bar with the highest strength of at least 50% or better. If not, you may need to fine-tune the dish and balance between the 11842 and the 12060 frequencies before scanning the new channel. 41. Press Yellow button to scan new channels 42. When Channel Scan is completed, pop up window displaying "Do you want to save?" with "Yes" highlighted yellow 43. Press OK button to save. Programming will automatically be displayed This completes the steps for scanning Adventist Channels. Following Are Optional steps: If you would like to view all available free programming from this satellite (this will include secular and international programming) There are aproximately 200 TV stations and 100 Radio stations on this satellite 44. Press P.SCAN button under blue Timer button 45. Press Channel up button to "Mode" line and push the Volume up button to display Scan FTA 46. Press Channel down button to Starn Scan line and press the OK button 47. POWER scan screen will appear and will list all available services on the satellite. Do not interrupt, this process may take up to ten minutes to complete 48. The prompt will show "Do you want to save?" with Yes highlighted yellow 49. Press the OK button to save. Prompt "Saving' will show and Power Scan screen will display. Press exit to view programming Deleting unwanted channels: 50. Press Ok/List button 51. Press the Blue button to Edit the channel list 52. Press the Channel down button to highlight Delete Channel 53. Press the OK button, a small gray button will appear next to each channel name 54. Use the Channel up and down button to highlight channel to be deleted 55. Press the OK button to mark the channel for deletion, the button will turn red 56. Repeat steps 54 and 55 until all unwanted channels are selected 57. Press the Blue button to DELETE, a prompt will display "Do you want to save?" use Vol down left arrow to select Yes highlighted yellow 58. Press the OK button, saving prompt will appear 59. Press exit to view programming Important Notice: Your FREE Adventist channel scanning instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment. If you require additional assistance, please contact the company or broadcaster where you originally purchased your satellite system. Fortec Star Lifetime Ultra Programming Instructions for 3ABN Proclaim   1. Using your  Fortec Star Lifetime Ultra remote control push “Menu” button 2. Press left arrow button to select System Setup menu screen 3. Press down arrow to select Factory Setting 4. Press the OK button 5. Prompt will request a password, enter 0000, prompt will ask for OK button to delete 6. Press the OK button, the receiver will restart 7. Press the Menu button 8. Press right arrow button to “INSTALLATION” screen with "Antenna Setup" highlighted 9. Press OK button to enter the Antenna Setup screen 10. Press left arrow button to unchek AMC4 101.0W 11. Press Channel up button to highlight “IA5/Ku 97.0W” 12. Press OK button to highlight "LNB type" 13. Press right arrow button to display “Standard” 14. Press EXIT button and a window will pop up on the screen displaying "INFO - Press ok to save or EXIT" 15. Press OK button to save 16. Press EXIT button to enter the Installation Screen with Antenna Setup highlighted 17. Press arrow up button to highlight “Advanced Scan” 18. Press OK button and a window will pop up on the screen “FTA” 19. Press OK button to dislpay the "Selected Satellite" window 20. Press OK button to enter the “ADVANCED SCAN” screen and “DOWN FREQUENCY” will be highlighted 21. Using the numeric keypad on the remote control enter the numbers 11842 22. Press down arrow button to “Symbol Rate” 23. With the number buttons on the remote control enter the numbers 22000 24. Press down arrow button to “Polarity” and press the right arrow button to display“Horizontal” 25. In the right hand side of the screen you will see two bars, one says “Level” and one says “Quality”. You should have a green “Level” bar (over 50%) 26. Verify green “Quality” bar to have highest strength of over 50%, press OK button to enter the “Channel Search” screen 27. When Channel Scan is completed, programming will automatically be displayed 28. Press Menu button, then right arrow button to go to Installation screen 29. Press arrow up or down button to highlight “Advanced Scan” 30. Press OK button and a prompt will appear Scan Mode "FTA” 31. Press OK button to display "Selected Satellite" window 32. Press OK button to enter the “ADVANCED SCAN” screen and “DOWN FREQUENCY” will be highlighted 33. Using the numeric keypad on the remote control enter the numbers 12060 34. Press down arrow button to “Symbol Rate” 35. With the numeric keypad on the remote control enter the numbers 22000 36. Press down arrow button to “Polarity” and press the right arrow button to display “Horizontal” 37. In the right hand side of the screen you will see two bars, one says “Level” and one says “Quality”. You should have a green “Level” bar over 50%. If not, you may need to fine-tune the dish and balance between the 11842 and the 12060 frequencies before scanning the new channel. 38. Verify green “Quality” bar to have highest strength of over 50%, press OK button to enter the “Channel Search” screen 39. When Channel Scan is completed, programming will automatically be displayed This completes the steps for scanning Adventist Channels. Following Are Optional steps: If you would like to view all available free programming from this satellite (this will include secular and international programming) There are aproximately 200 TV stations and 100 Radio stations on this satellite 40. Press the Menu button, then right arro to enter Installation Screen 41. Press down arrow button to select Power Scan, press OK button 42. Press down arrow button to highlight Scan, the press OK 43. Power Scan window will appear and will list all available list all available services on the satellite. Do not interrupt, this process may take up to ten minutes to complete 44. The receiver will automatically go to viewing mode Deleting Unwanted Channels: 45. Press Menu button then right arrow button twice to enter Channel Edit menu with TV channel highlighted 46. Press Ok to enter Channel Edit - TV menu 47. Press down arrow to highlight delete, then press OK to select channels to delete 48. Use up or down arrow buttons to highlight channel to delete 49. Press right arrow button to mark unwanted channel with red line through text 50. Repeat steps 48 and 49 until all unwanted channels are selected 51. Press the OK button twice to delete unwanted channels 52. Press Exit button four times to view programming Important Notice: Your FREE Adventist channel scanning instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment. If you require additional assistance, please contact the company or broadcaster where you originally purchased your satellite system. GEOSATpro 1000ci Programming Instructions for 3ABN Proclaim 1. Using your GEOSATpro 1000ci remote control place the receiver on the 3ABN channel 2. Press “Menu” button 3. Press the Channel down button (the button that points down) to highlight “INSTALLATION” 4. Press OK button to go to “PASSWORD” screen 5. Using the numeric keypad on the remote control enter 0000 6. Press the Channel down button to highlight “TP EDIT / SCAN” 7. Press OK button to display the “TP EDIT / SCAN” screen 8. Verify that Satellite Name displays IA-5/Ku, if not, press right arrow button to display IA-5/Ku 9. Press the Channel down button to highlight “TP FREQUENCY” 10. Using the numeric keypad on the remote control enter 12060 11. If necessary, press Channel down button to highlight “POLARIZATION” and press righ arrow button to display “Horizontal-18V” 12. Press Channel down to “SYMBOL RATE” 13. With the numeric keypad on the remote control enter the numbers 22000 14. Press Channel down button to highlight “Scan” and push the VOL up button until “FREE ONLY” is displayed 15. On the left side of the screen you will see a “SIGNAL QUALITY” strength indication bar. Verify signal quality is 50% or better, if not, you may need to fine-tune the dish and balance between the 11842 and the 12060 frequencies before scanning the new channel. 16. Press OK button to enter the “CHANNEL SCANNING” screen 17. When Channel Scan is completed, press exit four times to view programming Deleting unwanted channels: 18. Press CH/LIST button on the remote control to enter TV Channel List screen 19. Use channel up or down button to select unwanted channels 20. Press the Blue Delete button on the remote control, prompt will request a password, Enter 0000 21. Press Ok to delete the channel 22. Select additional channel to delete and press Blue Delete button on the remote 23. Press Ok button to delete the channel 24. Repeat steps 22 and 23 until all unwanted channels are deleted 25. Press Exit button to view programming Important Notice: Your FREE Adventist channel scanning instructions are provided below. Telephone assistance may be available at an additional charge for "Out Of Warranty" equipment. If you require additional assistance, please contact the company or broadcaster where you originally purchased your satellite system. BEC 1000 / 2000 Programming Instructions for 3ABN Proclaim 1. Place the BEC 1000 / 2000 satellite receiver on Channel 1 2. Using the remote control press the “MENU” button to display the "Channel List" screen 3. Press Right Arrow button to display "Channel Edit" screen with the TV icon highlighted 4. Press Enter button to display the “TV CH Edit” screen 5. Press Enter button to place a "X" to the left of the channel name 6. Press Down Arrow button to highlight the next channel name 7. Press Enter button to place a "X" to the left of the channel name 8. Repeat steps 6 and 7 until all channels have a "X" beside the channel name 9. Press Menu button to display a pop up window 10. Press Down Arrow 2 times to highlight "Delete" 11. Press Enter button 12. Press Return button to display the "Channel Edit" screen 13. Press Right Arrow button to display "Setup" screen with "CH Search" highlighted 14. Press Enter button to display "Channel Search" screen with "Satellite" highlighted 15. Press Down Arrow button to highlight "Frequency" 16. Using the numeric keypad, enter 11842 17. Press Down Arrow button to highlight "Symbol Rate" 18. Using the numeric keypad, enter 22000 19. Press Down Arrow button to highlight "Polarization" 20. Press Enter button to select "Horizontal" 21. Press Down Arrow button to “Scan” 22. Press Enter button to scan for new channels. When the scan is completed a popup window appears " Scan Message: Scan Complete" 23. Press the Return button to enter Channel Search screen. 24. Press Down Arrow button to highlight "Frequency" 25. Using the numeric keypad, enter 12060 26. Press Down Arrow button to highlight "Symbol Rate" 27. Using the numeric keypad, enter 22000 28. Press Down Arrow button to highlight "Polarization" 29. Press Enter button to select "Horizontal" 30. Press Down Arrow button to “Scan” 31. Press Enter button to scan for new channels. When the scan is completed a popup window appears " Scan Message: Scan Complete" 32. Press Return button 3 times to display a popup window "Confirm Save" with "OK" highlighted 33. Press Enter button. The receiver will restart and the new channels will be added to your channel list. Please note that the satellite name will be displayed as AMC4, but it really has been changed to the new satellite Galaxy 19. To Remove Unwanted Channels 34. press the “MENU” button to display the "Channel List" screen 35. Press Right Arrow button to display "Channel Edit" screen with the TV icon highlighted 36. Press Enter button to display the “TV CH Edit” screen 37. Press up or down button to highlight the unwanted channel 38. Press Enter button to place a "X" to the left of the channel name 39. Continue going down the list and mark all unwanted channels with an "X" besides them 40. Press Menu button to display a pop up window 41. Press Down Arrow 2 times to hightlight "Delete" 42. Press Enter button to delete 43. Press Return button twice, the prompt will show Confirm Save: Save Change To Database? 44. Press Enter to confirm, pop up window will show Confirm Save Information: Please Wait, Saving Data 45. View programming If your receiver is not listed here, please follow the instructions provided with your receiver on how to scan additional channels. Indicate the following: Transponder Frequency: 11842, Polarity: Horizontal Signal Bit Rate: 22000 Transponder Frequency: 12060, Polarity: Horizontal Signal Bit Rate: 22000 Now, scan in the new channels. If you would like to own a Glorystar receiver that updates automatically (so there is no need to do these steps for new or moved channels in the future), please call us at 866-597-0728 and ask the sales team for a Glorystar receiver to watch all the new and current Christian Channels including 3ABN, LLBN, Hope Channels as well as all new Adventist Channels.
Receiver Brand: Manhattan DSR 1500 - Instructions
Receiver Brand: Manhattan SKYLINE 1000 - Instructions
Receiver Brand: Topfield 3000Fi/4000/6200 Instructions
Receiver Brand: Fortec Star Mercury II - Instructions Glorystar System
Receiver Brand: Fortec Star Lifetime Ultra - Instructions
Receiver Brand: GEOSATpro DVR1000ci - Instructions Glorystar System
Receiver Brand: BEC 1000 / 2000 - Instructions
Other receivers